WhatSMD: identify an unknown SMD component

14 parts are printed A3

Not sure which one you have?

Answer up to 4 quick questions and these 14 parts are ranked, with a meter test that settles it. It works on a dead part too.

1N4448W-AUSOD-123Switching diode, 2 pins, PanjitSwitching diodeSOD-1232 pinsPanjit
What it is
Switching diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1N4448W-AU, opens in a new tab
1PS300SOT-323Switching diode, 3 pins, NexperiaSwitching diodeSOT-3233 pinsNexperia
What it is
Switching diode
Maker
Nexperia
Package
SOT-323
Pins
3
Details
Dual high-speed switching diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1PS300, opens in a new tab
1SS181SOT-23Switching diode, 3 pins, JSCJSwitching diodeSOT-233 pinsJSCJ
What it is
Switching diode
Maker
JSCJ
Package
SOT-23
Pins
3
Details
Switching diode, 80 V, 100 mA
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1SS181, opens in a new tab
AO3403SOT-23P-channel MOSFET, 3 pins, Alpha & Omega SemiconductorP-channel MOSFETSOT-233 pinsAlpha & Omega Semiconductor
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23
Pins
3
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO3403, opens in a new tab
AO3403LSOT-23P-channel MOSFET, 3 pins, Alpha & Omega SemiconductorP-channel MOSFETSOT-233 pinsAlpha & Omega Semiconductor
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23
Pins
3
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO3403L, opens in a new tab
MMBD4448SOT-23Switching diode, 3 pins, PanjitSwitching diodeSOT-233 pinsPanjit
What it is
Switching diode
Maker
Panjit
Package
SOT-23
Pins
3
Details
Switching diode, 75 V, 250 mA
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBD4448, opens in a new tab
MMBD4448WSOT-323Switching diode, 3 pins, PanjitSwitching diodeSOT-3233 pinsPanjit
What it is
Switching diode
Maker
Panjit
Package
SOT-323
Pins
3
Details
Switching diode, 75 V, 250 mA
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBD4448W, opens in a new tab
PMEG2005EHSOD-123FSchottky diode, 2 pins, NexperiaSchottky diodeSOD-123F2 pinsNexperia
What it is
Schottky diode
Maker
Nexperia
Package
SOD-123F
Pins
2
Details
20 V, 0.5 A very low VF MEGA Schottky barrier rectifier
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PMEG2005EH, opens in a new tab
PMEG3020EPSOD-128Schottky diode, 2 pins, NexperiaSchottky diodeSOD-1282 pinsNexperia
What it is
Schottky diode
Maker
Nexperia
Package
SOD-128
Pins
2
Details
30 V, 2 A low VF Schottky barrier rectifier
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PMEG3020EP, opens in a new tab
UMA3NSOT-353Digital transistor (PNP, resistors built in), 5 pins, JSCJDigital transistor (PNP, resistors built in)SOT-3535 pinsJSCJ
What it is
Digital transistor (PNP, resistors built in)
Maker
JSCJ
Package
SOT-353
Pins
5
Details
Digital transistor (bias resistors built in), PNP, 100 mA
Source
From the manufacturer's datasheet
Is it dead?
Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
Working, it reads
Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
Dead, it reads
Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
Base to emitter near 0 Ω: failed short.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor UMA3N, opens in a new tab
4 more parts have no package on record
- BZX884B15LZener diode, VishayZener diodeNot recordedNot recordedVishay
  What it is
  Zener diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  15 V Zener diode
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BZX884B15L, opens in a new tab
- ESD206-B1-02ELESD protection diode, InfineonESD protection diodeNot recordedNot recordedInfineon
  What it is
  ESD protection diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESD206-B1-02EL, opens in a new tab
- SDB13HSSchottky diode, DiotecSchottky diodeNot recordedNot recordedDiotec
  What it is
  Schottky diode
  Maker
  Diotec
  Package
  Not recorded
  Pins
  Not recorded
  Details
  SMD Low Barrier Schottky Rectifier Diodes
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SDB13HS, opens in a new tab
- TPS3831A09DQNVoltage supervisor, 4 pins, Texas InstrumentsVoltage supervisorNot recorded4 pinsTexas Instruments
  What it is
  Voltage supervisor
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  4
  Details
  150-nA, Ultralow Power, Supply Voltage Monitor
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TPS3831A09DQN, opens in a new tab

15 more parts have codes that begin with A3

Codes that begin with A3

For a marking with its end worn or burnt off. Each one shows its full printed code.

1PS181printed A3TSOT-23Switching diode, 3 pins, NexperiaSwitching diodeSOT-233 pinsNexperia
Printed A3T. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Switching diode
Maker
Nexperia
Package
SOT-23
Pins
3
Details
High-speed double diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1PS181, opens in a new tab
PJA3430printed A30SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A30. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3430, opens in a new tab
PJA3431printed A31SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A31. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3431, opens in a new tab
PJA3432printed A32SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A32. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3432, opens in a new tab
PJA3432-AUprinted A32SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A32. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3432-AU, opens in a new tab
PJA3433printed A33SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A33. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3433, opens in a new tab
PJA3433-AUprinted A33SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A33. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3433-AU, opens in a new tab
PJA3434printed A34SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A34. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3434, opens in a new tab
PJA3435printed A35SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A35. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3435, opens in a new tab
PJA3436printed A36SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A36. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3436, opens in a new tab
PJA3438printed A38SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A38. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3438, opens in a new tab
PJA3438-AUprinted A38SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A38. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3438-AU, opens in a new tab
PJA3439printed A39SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A39. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3439, opens in a new tab
PJA3439-AUprinted A39SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
Printed A39. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3439-AU, opens in a new tab
SN74AHC1G32DBVprinted A32LSOT-23-5Logic gate, 5 pins, Texas InstrumentsLogic gateSOT-23-55 pinsTexas Instruments
Printed A32L. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Logic gate
Maker
Texas Instruments
Package
SOT-23-5
Pins
5
Details
Single 2-Input Positive-OR Gate
Source
From the manufacturer's datasheet
Is it dead?
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor SN74AHC1G32DBV, opens in a new tab

One code, several parts

Marking codes are not unique. In the standard code book, 6H on a SOT-23 is an NPN transistor, a varicap, an N-channel JFET, two digital transistors, a 3.6 V voltage detector: six parts from five makers. So a search shows the parts we hold under that code and under codes easily misread as it, with only the columns that tell them apart.

6Hon a SOT-23, in the code book

NPN transistor
Varicap
N-channel JFET
Digital transistor ×2
3.6 V voltage detector

When more than one is left

Tap Help me choose. Up to 4 quick answers: whether the part has failed, then what separates the parts left. Those get ranked with the reasoning and a test that settles it. That uses one identification; 3 a month are free.

When you cannot read it

Tap the camera in the field. We read the characters, keep the ones we are unsure of, and search every reading. A photo too soft to read is turned back on your phone first; if it is the only one you can get, you can still send it.

What’s printed on it?

14 parts are printed A3

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Codes that begin with A3

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

One code, several parts

When more than one is left

When you cannot read it