SMD marking

A7in SOT-23

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

9 parts are printed A7

Not sure which one you have?

Answer up to 4 quick questions and these 9 parts are ranked, with a meter test that settles it. It works on a dead part too.

AO3407SOT-23P-channel MOSFET, 3 pins, Alpha & Omega SemiconductorP-channel MOSFET3 pinsAlpha & Omega Semiconductor
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23
Pins
3
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO3407, opens in a new tab
AO3407LSOT-23P-channel MOSFET, 3 pins, Alpha & Omega SemiconductorP-channel MOSFET3 pinsAlpha & Omega Semiconductor
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23
Pins
3
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO3407L, opens in a new tab
BAV99SOT-23Switching diode, 3 pins, InfineonSwitching diode3 pinsInfineon
What it is
Switching diode
Maker
Infineon
Package
SOT-23
Pins
3
Details
Dual surface-mount switching diode, series
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAV99, opens in a new tab
BAV99HSOT-23Switching diode, 3 pins, Taiwan SemiconductorSwitching diode3 pinsTaiwan Semiconductor
What it is
Switching diode
Maker
Taiwan Semiconductor
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAV99H, opens in a new tab
BAV99LSOT-23Switching diode, 3 pins, DiotecSwitching diode3 pinsDiotec
What it is
Switching diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Small Signal Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAV99L, opens in a new tab
MMBD4148SESOT-23Switching diode, 3 pins, Taiwan SemiconductorSwitching diode3 pinsTaiwan Semiconductor
What it is
Switching diode
Maker
Taiwan Semiconductor
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBD4148SE, opens in a new tab
3 more parts have no package on record. Nothing rules them out, so they stay.
- S1JMRectifier, Taiwan SemiconductorRectifierNot recordedTaiwan Semiconductor
  What it is
  Rectifier
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways: failed open.
  A reading the wrong way round as well: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor S1JM, opens in a new tab
- S1JMHRectifier, Taiwan SemiconductorRectifierNot recordedTaiwan Semiconductor
  What it is
  Rectifier
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways: failed open.
  A reading the wrong way round as well: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor S1JMH, opens in a new tab
- TPS3831G33DQNVoltage supervisor, 4 pins, Texas InstrumentsVoltage supervisor4 pinsTexas Instruments
  What it is
  Voltage supervisor
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  4
  Details
  150-nA, Ultralow Power, Supply Voltage Monitor
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TPS3831G33DQN, opens in a new tab

8 more parts are printed with a code easy to misread as A7

Printed with a code easy to misread

One character differs, and it is one that is easy to confuse under a lamp. The odd one out is marked on each.

AO3424printed ATSOT-23MOSFET, 3 pins, Alpha & Omega SemiconductorMOSFET3 pinsAlpha & Omega Semiconductor
Printed AT on the part. Easy to misread as A7. Check that character with a loupe before you order anything.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23
Pins
3
Details
Low-voltage (12-30 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO3424, opens in a new tab
AO3424Lprinted ATSOT-23MOSFET, 3 pins, Alpha & Omega SemiconductorMOSFET3 pinsAlpha & Omega Semiconductor
Printed AT on the part. Easy to misread as A7. Check that character with a loupe before you order anything.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23
Pins
3
Details
Low-voltage (12-30 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO3424L, opens in a new tab
6 more parts have no package on record. Nothing rules them out, so they stay.
- BFP540printed ATRF transistor, InfineonRF transistorNot recordedInfineon
  Printed AT on the part. Easy to misread as A7. Check that character with a loupe before you order anything.
  What it is
  RF transistor
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or its base leg off the pad.
  Working, it reads
  From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
  Dead, it reads
  Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  A reading the wrong way round, where it should be open: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BFP540, opens in a new tab
- BZX884B8V2Lprinted ATZener diode, VishayZener diodeNot recordedVishay
  Printed AT on the part. Easy to misread as A7. Check that character with a loupe before you order anything.
  What it is
  Zener diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  8.2 V Zener diode
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BZX884B8V2L, opens in a new tab
- MSMP8.5Aprinted ATTVS diode, VishayTVS diodeNot recordedVishay
  Printed AT on the part. Easy to misread as A7. Check that character with a loupe before you order anything.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  150 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor MSMP8.5A, opens in a new tab
- SMBG8.5Aprinted ATTVS diode, VishayTVS diodeNot recordedVishay
  Printed AT on the part. Easy to misread as A7. Check that character with a loupe before you order anything.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMBG8.5A, opens in a new tab
- TLV70725PDQNprinted ATLDO regulator, 4 pins, Texas InstrumentsLDO regulator4 pinsTexas Instruments
  Printed AT on the part. Easy to misread as A7. Check that character with a loupe before you order anything.
  What it is
  LDO regulator
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  4
  Details
  200-mA, Low-IQ, Low-Noise, Low-Dropout Regulator for Portable Devices
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TLV70725PDQN, opens in a new tab
- VESD05A6A-HAFprinted ATESD protection diode, VishayESD protection diodeNot recordedVishay
  Printed AT on the part. Easy to misread as A7. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  6-Line ESD Protection Diode Array in LLP75
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor VESD05A6A-HAF, opens in a new tab

20 more parts have codes that begin with A7

Codes that begin with A7

For a marking with its end worn or burnt off. Each one shows its full printed code.

BAS70-AUprinted A70SOT-23Schottky diode, 3 pins, PanjitSchottky diode3 pinsPanjit
Printed A70. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Schottky diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAS70-AU, opens in a new tab
BAS70A-AUprinted A72SOT-23Schottky diode, 3 pins, PanjitSchottky diode3 pinsPanjit
Printed A72. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Schottky diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAS70A-AU, opens in a new tab
BAS70C-AUprinted A73SOT-23Schottky diode, 3 pins, PanjitSchottky diode3 pinsPanjit
Printed A73. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Schottky diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAS70C-AU, opens in a new tab
BAS70S-AUprinted A74SOT-23Schottky diode, 3 pins, PanjitSchottky diode3 pinsPanjit
Printed A74. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Schottky diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAS70S-AU, opens in a new tab
BSS123printed A76SOT-23N-channel MOSFET, 3 pins, PanjitN-channel MOSFET3 pinsPanjit
Printed A76. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
N-channel MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Details
MOSFET, N-channel, 100 V, 0.17 A
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BSS123, opens in a new tab
PJA3470printed A70SOT-23MOSFET, 3 pins, PanjitMOSFET3 pinsPanjit
Printed A70. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3470, opens in a new tab
PJA3471printed A71SOT-23MOSFET, 3 pins, PanjitMOSFET3 pinsPanjit
Printed A71. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3471, opens in a new tab
PJA3474Sprinted A78SOT-23MOSFET, 3 pins, PanjitMOSFET3 pinsPanjit
Printed A78. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3474S, opens in a new tab
PJA3474S-AUprinted A78SOT-23MOSFET, 3 pins, PanjitMOSFET3 pinsPanjit
Printed A78. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3474S-AU, opens in a new tab
PJA3476printed A76SOT-23MOSFET, 3 pins, PanjitMOSFET3 pinsPanjit
Printed A76. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3476, opens in a new tab
PJA3476-AUprinted A76SOT-23MOSFET, 3 pins, PanjitMOSFET3 pinsPanjit
Printed A76. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJA3476-AU, opens in a new tab
9 more parts have no package on record. Nothing rules them out, so they stay.
- AOZ2231CQI-01printed ATC1DC DC converter, Alpha & Omega SemiconductorDC DC converterNot recordedAlpha & Omega Semiconductor
  Printed ATC1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  DC DC converter
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Synchronous buck regulator
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ2231CQI-01, opens in a new tab
- AOZ2231CQI-21printed ATCPDC DC converter, Alpha & Omega SemiconductorDC DC converterNot recordedAlpha & Omega Semiconductor
  Printed ATCP. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  DC DC converter
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Synchronous buck regulator
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ2231CQI-21, opens in a new tab
- AOZ2231CQI-23printed ATCSDC DC converter, Alpha & Omega SemiconductorDC DC converterNot recordedAlpha & Omega Semiconductor
  Printed ATCS. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  DC DC converter
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Synchronous buck regulator
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ2231CQI-23, opens in a new tab
- TA6F12Aprinted ATPTVS diode, VishayTVS diodeNot recordedVishay
  Printed ATP. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TA6F12A, opens in a new tab
- TA6F12CAprinted ATPTVS diode, VishayTVS diodeNot recordedVishay
  Printed ATP. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, bidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TA6F12CA, opens in a new tab
- TA6L12Aprinted ATLTVS diode, VishayTVS diodeNot recordedVishay
  Printed ATL. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TA6L12A, opens in a new tab
- TA6L12CAprinted ATLTVS diode, VishayTVS diodeNot recordedVishay
  Printed ATL. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, bidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TA6L12CA, opens in a new tab
- TPSMA6L8.5Aprinted ATATVS diode, DiotecTVS diodeNot recordedDiotec
  Printed ATA. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Diotec
  Package
  Not recorded
  Pins
  Not recorded
  Details
  SMD Transient Voltage Suppressor Diodes
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TPSMA6L8.5A, opens in a new tab
- TPSMP12Aprinted ATPTVS diode, VishayTVS diodeNot recordedVishay
  Printed ATP. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  400 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TPSMP12A, opens in a new tab

Open this in the search to correct a character or try another package.

9 parts are printed A7

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Printed with a code easy to misread

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Codes that begin with A7

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?