WhatSMD: identify an unknown SMD component

3 parts are printed 0

Not sure which one you have?

Answer up to 4 quick questions and these 3 parts are ranked, with a meter test that settles it. It works on a dead part too.

all Alpha & Omega Semiconductor. What differs:

AOC2870Dual N-channel MOSFETDual N-channel MOSFET
What it is
Dual N-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Details
Common-drain dual N-channel battery MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOC2870, opens in a new tab
AOZ8S411ULS-24ESD protection diodeESD protection diode
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Details
ESD protection for high-speed interfaces
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8S411ULS-24, opens in a new tab
AOZ8S516UDS-20ESD protection diodeESD protection diode
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8S516UDS-20, opens in a new tab

25 more parts are printed with a code easy to misread as 0

Printed with a code easy to misread

One character differs, and it is one that is easy to confuse under a lamp. The odd one out is marked on each.

IRLTS6342printed OSOT-23-6N-channel MOSFET, 6 pins, InfineonN-channel MOSFET6 pinsInfineon
Printed O on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
What it is
N-channel MOSFET
Maker
Infineon
Package
SOT-23-6
Pins
6
Details
30V Single N-Channel StrongIRFET™ MOSFET in a TSOP-6 (Micro 6) package
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor IRLTS6342, opens in a new tab
24 more parts have no package on record. Nothing rules them out, so they stay.
- AOCA32116Eprinted DDual N-channel MOSFET, Alpha & Omega SemiconductorDual N-channel MOSFETNot recordedAlpha & Omega Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  Dual N-channel MOSFET
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Common-drain dual N-channel battery MOSFET
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.
  Working, it reads
  Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOCA32116E, opens in a new tab
- AOZ8S331BDS-03printed DESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection for high-speed interfaces
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8S331BDS-03, opens in a new tab
- AOZ8S530BLS-03printed DESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8S530BLS-03, opens in a new tab
- AOZ1353LI-02printed DLoad switch, Alpha & Omega SemiconductorLoad switchNot recordedAlpha & Omega Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  Load switch
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  USB Type-C protection switch
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage, board powered, black probe on ground.
  Working, it reads
  Switched on, the output pin sits at the input voltage. Switched off, it sits near 0 V.
  Dead, it reads
  Output at the input voltage while switched off: the pass element has shorted.
  Input present and switched on, no output: failed open, or shut down into a shorted load. Power off and measure output to ground.
  On the board:
  An output near 0 Ω to ground is usually the load. Lift the output pin to see which.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The pinout and whether the enable is active high or low differ between parts. The datasheet gives both.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ1353LI-02, opens in a new tab
- AOZ8310DI-20printed DESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8310DI-20, opens in a new tab
- AOZ8331DI-05printed DESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8331DI-05, opens in a new tab
- BAR64-02LRHprinted OPIN diode, InfineonPIN diodeNot recordedInfineon
  Printed O on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  PIN diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.6 to 0.9 V anode to cathode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BAR64-02LRH, opens in a new tab
- BAS21-03Wprinted DSwitching diode, InfineonSwitching diodeNot recordedInfineon
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  Switching diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways: failed open.
  A reading the wrong way round as well: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BAS21-03W, opens in a new tab
- BAT14-03Wprinted OSchottky diode, InfineonSchottky diodeNot recordedInfineon
  Printed O on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  Schottky diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BAT14-03W, opens in a new tab
- ESD204-B1-02ELSprinted DESD protection diode, InfineonESD protection diodeNot recordedInfineon
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESD204-B1-02ELS, opens in a new tab
- ESDHB5V0AE1printed OESD protection diode, JSCJESD protection diodeNot recordedJSCJ
  Printed O on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection diode, VRWM 5.5 V
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESDHB5V0AE1, opens in a new tab
- IRLML5103printed DP-channel MOSFET, InfineonP-channel MOSFETNot recordedInfineon
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  P-channel MOSFET
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Details
  -30V Single P-Channel Power MOSFET in a Micro 3 package
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor IRLML5103, opens in a new tab
- PJSD12TMprinted dESD protection diode, PanjitESD protection diodeNot recordedPanjit
  Printed d on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Panjit
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PJSD12TM, opens in a new tab
- PS160M-D32printed QESD protection diode, PanjitESD protection diodeNot recordedPanjit
  Printed Q on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Panjit
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PS160M-D32, opens in a new tab
- PS1705-D32printed DESD protection diode, PanjitESD protection diodeNot recordedPanjit
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Panjit
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PS1705-D32, opens in a new tab
- RB520SM5-40printed DSchottky diode, Taiwan SemiconductorSchottky diodeNot recordedTaiwan Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  Schottky diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor RB520SM5-40, opens in a new tab
- SS22Mprinted DSchottky diode, Taiwan SemiconductorSchottky diodeNot recordedTaiwan Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  Schottky diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Rectifier schottky
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SS22M, opens in a new tab
- SS22MHprinted DSchottky diode, Taiwan SemiconductorSchottky diodeNot recordedTaiwan Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  Schottky diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Rectifier schottky
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SS22MH, opens in a new tab
- TESDH5V0B05P1Q1printed DESD protection diode, Taiwan SemiconductorESD protection diodeNot recordedTaiwan Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TESDH5V0B05P1Q1, opens in a new tab
- TESDL24VB17P1Q1printed DESD protection diode, Taiwan SemiconductorESD protection diodeNot recordedTaiwan Semiconductor
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TESDL24VB17P1Q1, opens in a new tab
- TLV803EA36DPWprinted DVoltage supervisor, 5 pins, Texas InstrumentsVoltage supervisor5 pinsTexas Instruments
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  Voltage supervisor
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  5
  Details
  Low Power 250-nA IQ and Small Size Supply Voltage Supervisors
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TLV803EA36DPW, opens in a new tab
- TMP112D2IDPWprinted OTemperature sensor, 5 pins, Texas InstrumentsTemperature sensor5 pinsTexas Instruments
  Printed O on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  Temperature sensor
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  5
  Details
  High-Accuracy, Low-Power, Digital Temperature Sensors With SMBus and Two-Wire Serial Interface in SOT563 and X2SON...
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TMP112D2IDPW, opens in a new tab
- VBUS54DD-HS4printed DESD protection diode, VishayESD protection diodeNot recordedVishay
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  4-Line BUS-Port ESD Protection
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor VBUS54DD-HS4, opens in a new tab
- VESD05A1B-HD1printed DESD protection diode, VishayESD protection diodeNot recordedVishay
  Printed D on the part. Easy to misread as 0. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD Protection Diode in LLP1006-2L
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor VESD05A1B-HD1, opens in a new tab

22 more parts have codes that begin with 0

Codes that begin with 0

For a marking with its end worn or burnt off. Each one shows its full printed code.

AO6400printed D0SOT-23-6MOSFET, 6 pins, Alpha & Omega SemiconductorMOSFET6 pinsAlpha & Omega Semiconductor
Printed D0. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
Low-voltage (12-30 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6400, opens in a new tab
AO6400Lprinted D0SOT-23-6MOSFET, 6 pins, Alpha & Omega SemiconductorMOSFET6 pinsAlpha & Omega Semiconductor
Printed D0. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
Low-voltage (12-30 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6400L, opens in a new tab
AO6403printed D3SOT-23-6P-channel MOSFET, 6 pins, Alpha & Omega SemiconductorP-channel MOSFET6 pinsAlpha & Omega Semiconductor
Printed D3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6403, opens in a new tab
AO6403Lprinted D3SOT-23-6P-channel MOSFET, 6 pins, Alpha & Omega SemiconductorP-channel MOSFET6 pinsAlpha & Omega Semiconductor
Printed D3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6403L, opens in a new tab
AO6404printed D4SOT-23-6MOSFET, 6 pins, Alpha & Omega SemiconductorMOSFET6 pinsAlpha & Omega Semiconductor
Printed D4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
Low-voltage (12-30 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6404, opens in a new tab
AO6404Lprinted D4SOT-23-6MOSFET, 6 pins, Alpha & Omega SemiconductorMOSFET6 pinsAlpha & Omega Semiconductor
Printed D4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
Low-voltage (12-30 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6404L, opens in a new tab
AO6405printed D5SOT-23-6P-channel MOSFET, 6 pins, Alpha & Omega SemiconductorP-channel MOSFET6 pinsAlpha & Omega Semiconductor
Printed D5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6405, opens in a new tab
AO6405Lprinted D5SOT-23-6P-channel MOSFET, 6 pins, Alpha & Omega SemiconductorP-channel MOSFET6 pinsAlpha & Omega Semiconductor
Printed D5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6405L, opens in a new tab
AO6415printed DFSOT-23-6P-channel MOSFET, 6 pins, Alpha & Omega SemiconductorP-channel MOSFET6 pinsAlpha & Omega Semiconductor
Printed DF. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6415, opens in a new tab
AO6415Lprinted DFSOT-23-6P-channel MOSFET, 6 pins, Alpha & Omega SemiconductorP-channel MOSFET6 pinsAlpha & Omega Semiconductor
Printed DF. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6415L, opens in a new tab
AO6420printed DNSOT-23-6MOSFET, 6 pins, Alpha & Omega SemiconductorMOSFET6 pinsAlpha & Omega Semiconductor
Printed DN. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
Medium-voltage (40-400 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6420, opens in a new tab
AO6420Lprinted DNSOT-23-6MOSFET, 6 pins, Alpha & Omega SemiconductorMOSFET6 pinsAlpha & Omega Semiconductor
Printed DN. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
Medium-voltage (40-400 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6420L, opens in a new tab
AO6424printed DTSOT-23-6MOSFET, 6 pins, Alpha & Omega SemiconductorMOSFET6 pinsAlpha & Omega Semiconductor
Printed DT. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
Low-voltage (12-30 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6424, opens in a new tab
AO6424Lprinted DTSOT-23-6MOSFET, 6 pins, Alpha & Omega SemiconductorMOSFET6 pinsAlpha & Omega Semiconductor
Printed DT. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23-6
Pins
6
Details
Low-voltage (12-30 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AO6424L, opens in a new tab
MMFTN620KDprinted QESOT-23-6MOSFET, 6 pins, DiotecMOSFET6 pinsDiotec
Printed QE. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Diotec
Package
SOT-23-6
Pins
6
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMFTN620KD, opens in a new tab
TPS61165DBVprinted DAKSOT-23-6DC DC converter, 6 pins, Texas InstrumentsDC DC converter6 pinsTexas Instruments
Printed DAK. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
DC DC converter
Maker
Texas Instruments
Package
SOT-23-6
Pins
6
Details
High-Brightness, White LED Driver in WSON and SOT-23 Packages
Source
From the manufacturer's datasheet
Is it dead?
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor TPS61165DBV, opens in a new tab
6 more parts have no package on record. Nothing rules them out, so they stay.
- CJMPD08printed 08Dual P-channel MOSFET, JSCJDual P-channel MOSFETNot recordedJSCJ
  Printed 08. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Dual P-channel MOSFET
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.
  Working, it reads
  Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor CJMPD08, opens in a new tab
- DTC114TEprinted 04Digital transistor (NPN, resistors built in), JSCJDigital transistor (NPN, resistors built in)Not recordedJSCJ
  Printed 04. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Digital transistor (NPN, resistors built in)
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Digital transistor (bias resistors built in), NPN
  Source
  From the manufacturer's datasheet
  Is it dead?
  Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
  Working, it reads
  Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
  Dead, it reads
  Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  Base to emitter near 0 Ω: failed short.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
  Watch for:
  On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor DTC114TE, opens in a new tab
- DTC144TEprinted 06Digital transistor (NPN, resistors built in), JSCJDigital transistor (NPN, resistors built in)Not recordedJSCJ
  Printed 06. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Digital transistor (NPN, resistors built in)
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Digital transistor (bias resistors built in), NPN
  Source
  From the manufacturer's datasheet
  Is it dead?
  Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
  Working, it reads
  Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
  Dead, it reads
  Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  Base to emitter near 0 Ω: failed short.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
  Watch for:
  On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor DTC144TE, opens in a new tab
- ESDH5V0FD1printed 04PESD protection diode, JSCJESD protection diodeNot recordedJSCJ
  Printed 04P. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  ESD protection diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection diode, VRWM 5 V
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESDH5V0FD1, opens in a new tab
- ESDTU5V0AG4Bprinted 0524PESD protection diode, JSCJESD protection diodeNot recordedJSCJ
  Printed 0524P. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  ESD protection diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection diode, VRWM 5 V
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESDTU5V0AG4B, opens in a new tab
- ESDUNF7V0B1printed 07ESD protection diode, JSCJESD protection diodeNot recordedJSCJ
  Printed 07. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  ESD protection diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection diode, VRWM 7 V
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESDUNF7V0B1, opens in a new tab

One code, several parts

Marking codes are not unique. In the standard code book, 6H on a SOT-23 is an NPN transistor, a varicap, an N-channel JFET, two digital transistors, a 3.6 V voltage detector: six parts from five makers. So a search shows the parts we hold under that code and under codes easily misread as it, with only the columns that tell them apart.

6Hon a SOT-23, in the code book

NPN transistor
Varicap
N-channel JFET
Digital transistor ×2
3.6 V voltage detector

When more than one is left

Tap Help me choose. Up to 4 quick answers: whether the part has failed, then what separates the parts left. Those get ranked with the reasoning and a test that settles it. That uses one identification; 3 a month are free.

When you cannot read it

Tap the camera in the field. We read the characters, keep the ones we are unsure of, and search every reading. A photo too soft to read is turned back on your phone first; if it is the only one you can get, you can still send it.

What’s printed on it?

3 parts are printed 0

Is it dead?

Is it dead?

Is it dead?

Printed with a code easy to misread

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Codes that begin with 0

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

One code, several parts

When more than one is left

When you cannot read it