SMD marking

U

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

12 parts are printed U

Not sure which one you have?

Answer up to 4 quick questions and these 12 parts are ranked, with a meter test that settles it. It works on a dead part too.

AOZ8S321UD4-03ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Details
ESD protection for high-speed interfaces
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8S321UD4-03, opens in a new tab
AOZ8S321UD4-05ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Details
ESD protection for high-speed interfaces
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8S321UD4-05, opens in a new tab
AOZ8S507BDS-07ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8S507BDS-07, opens in a new tab
AOZ8S530BLS-05ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8S530BLS-05, opens in a new tab
AOZ8310ADI-04ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8310ADI-04, opens in a new tab
AOZ8851ADI-18ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Details
ESD protection for high-speed interfaces
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8851ADI-18, opens in a new tab
BAR88-02VPIN diode, InfineonPIN diodeNot recordedInfineon
What it is
PIN diode
Maker
Infineon
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.6 to 0.9 V anode to cathode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAR88-02V, opens in a new tab
BB545InfineonNot recordedNot recordedInfineon
What it is
Not recorded
Maker
Infineon
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
Open between every pair of pins: failed open, or a part that reads open when working.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BB545, opens in a new tab
IRLML6344N-channel MOSFET, InfineonN-channel MOSFETNot recordedInfineon
What it is
N-channel MOSFET
Maker
Infineon
Package
Not recorded
Pins
Not recorded
Details
30V Single N-Channel StrongIRFET™ Power MOSFET in a SOT-23 package
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor IRLML6344, opens in a new tab
PESD3V3Z1BSFESD protection diode, 2 pins, NexperiaESD protection diode2 pinsNexperia
What it is
ESD protection diode
Maker
Nexperia
Package
Not recorded
Pins
2
Details
Extremely low capacitance bidirectional ESD protection diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PESD3V3Z1BSF, opens in a new tab
PESD4V0Z1BSFESD protection diode, 2 pins, NexperiaESD protection diode2 pinsNexperia
What it is
ESD protection diode
Maker
Nexperia
Package
Not recorded
Pins
2
Details
Extremely low capacitance bidirectional ESD protection diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PESD4V0Z1BSF, opens in a new tab
VCUT07B1-HD1ESD protection diode, VishayESD protection diodeNot recordedVishay
What it is
ESD protection diode
Maker
Vishay
Package
Not recorded
Pins
Not recorded
Details
Bidirectional Symmetrical (BiSy) Single Line ESD Protection Diode in LLP1006-2L
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor VCUT07B1-HD1, opens in a new tab

38 more parts have codes that begin with U

Codes that begin with U

For a marking with its end worn or burnt off. Each one shows its full printed code.

BCX19printed U1SOT-23NPN transistor, 3 pins, JSCJNPN transistorSOT-233 pinsJSCJ
Printed U1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
NPN transistor
Maker
JSCJ
Package
SOT-23
Pins
3
Details
Bipolar transistor, NPN, 45 V, 0.5 A
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or its base leg off the pad.
Working, it reads
Red probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
Only one junction reads, or none: a junction has failed open. It then looks like a diode.
A reading the wrong way round, where it should be open: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BCX19, opens in a new tab
BZT52B2V2printed U6SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U6. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
522.2 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B2V2, opens in a new tab
BZT52B2V2-Gprinted U6SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U6. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
522.2 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B2V2-G, opens in a new tab
BZT52B51printed U1SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B51, opens in a new tab
BZT52B51-Gprinted U1SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
5251 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B51-G, opens in a new tab
BZT52B56printed U2SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U2. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B56, opens in a new tab
BZT52B56-Gprinted U2SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U2. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
5256 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B56-G, opens in a new tab
BZT52B62printed U3SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B62, opens in a new tab
BZT52B62-Gprinted U3SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
5262 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B62-G, opens in a new tab
BZT52B68printed U4SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B68, opens in a new tab
BZT52B68-Gprinted U4SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
5268 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B68-G, opens in a new tab
BZT52B75printed U5SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B75, opens in a new tab
BZT52B75-Gprinted U5SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
Printed U5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
5275 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52B75-G, opens in a new tab
BZX84J-C2V4printed U3SOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed U3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
2.4 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C2V4, opens in a new tab
BZX84J-C2V7printed U4SOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed U4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
2.7 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C2V7, opens in a new tab
BZX84J-C3V0printed U9SOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed U9. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
3.0 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C3V0, opens in a new tab
BZX84J-C3V3printed UASOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UA. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
3.3 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C3V3, opens in a new tab
BZX84J-C3V6printed UBSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UB. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
3.6 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C3V6, opens in a new tab
BZX84J-C3V9printed UCSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UC. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
3.9 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C3V9, opens in a new tab
BZX84J-C4V3printed UFSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UF. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
4.3 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C4V3, opens in a new tab
BZX84J-C4V7printed UGSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UG. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
4.7 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C4V7, opens in a new tab
BZX84J-C5V1printed ULSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UL. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
5.1 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C5V1, opens in a new tab
BZX84J-C5V6printed UMSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UM. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
5.6 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C5V6, opens in a new tab
BZX84J-C6V2printed URSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UR. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
6.2 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C6V2, opens in a new tab
BZX84J-C6V8printed USSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed US. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
6.8 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C6V8, opens in a new tab
BZX84J-C7V5printed UUSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UU. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
7.5 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C7V5, opens in a new tab
BZX84J-C8V2printed UVSOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
Printed UV. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Nexperia
Package
SOD-323
Pins
2
Details
8.2 V approx. ±5% voltage regulator (Zener) diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84J-C8V2, opens in a new tab
11 more parts have no package on record
- BAR88-02Lprinted UUPIN diode, InfineonPIN diodeNot recordedNot recordedInfineon
  Printed UU. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  PIN diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.6 to 0.9 V anode to cathode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BAR88-02L, opens in a new tab
- BAR88-02LRHprinted U8PIN diode, InfineonPIN diodeNot recordedNot recordedInfineon
  Printed U8. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  PIN diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.6 to 0.9 V anode to cathode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BAR88-02LRH, opens in a new tab
- BAR88-099L4printed USPIN diode, InfineonPIN diodeNot recordedNot recordedInfineon
  Printed US. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  PIN diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.6 to 0.9 V anode to cathode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BAR88-099L4, opens in a new tab
- BCR101L3printed UCDigital transistor (resistors built in), InfineonDigital transistor (resistors built in)Not recordedNot recordedInfineon
  Printed UC. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Digital transistor (resistors built in)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
  Working, it reads
  Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
  Dead, it reads
  Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  Base to emitter near 0 Ω: failed short.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
  Watch for:
  On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BCR101L3, opens in a new tab
- BCR114Fprinted U4Digital transistor (resistors built in), InfineonDigital transistor (resistors built in)Not recordedNot recordedInfineon
  Printed U4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Digital transistor (resistors built in)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
  Working, it reads
  Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
  Dead, it reads
  Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  Base to emitter near 0 Ω: failed short.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
  Watch for:
  On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BCR114F, opens in a new tab
- BCR149Fprinted UADigital transistor (resistors built in), InfineonDigital transistor (resistors built in)Not recordedNot recordedInfineon
  Printed UA. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Digital transistor (resistors built in)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
  Working, it reads
  Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
  Dead, it reads
  Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  Base to emitter near 0 Ω: failed short.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
  Watch for:
  On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BCR149F, opens in a new tab
- BCR151Fprinted UDDigital transistor (resistors built in), InfineonDigital transistor (resistors built in)Not recordedNot recordedInfineon
  Printed UD. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Digital transistor (resistors built in)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
  Working, it reads
  Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
  Dead, it reads
  Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  Base to emitter near 0 Ω: failed short.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
  Watch for:
  On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BCR151F, opens in a new tab
- BCR164Fprinted U6Digital transistor (resistors built in), InfineonDigital transistor (resistors built in)Not recordedNot recordedInfineon
  Printed U6. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Digital transistor (resistors built in)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
  Working, it reads
  Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
  Dead, it reads
  Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  Base to emitter near 0 Ω: failed short.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
  Watch for:
  On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BCR164F, opens in a new tab
- BCR199Fprinted UBDigital transistor (resistors built in), InfineonDigital transistor (resistors built in)Not recordedNot recordedInfineon
  Printed UB. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Digital transistor (resistors built in)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
  Working, it reads
  Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
  Dead, it reads
  Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  Base to emitter near 0 Ω: failed short.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
  Watch for:
  On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BCR199F, opens in a new tab
- BGX50Aprinted U1RF amplifier (MMIC), InfineonRF amplifier (MMIC)Not recordedNot recordedInfineon
  Printed U1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  RF amplifier (MMIC)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage, board powered, on the output pin that the bias resistor or choke feeds.
  Working, it reads
  The output pin sits at the device voltage the datasheet gives, a few volts, below the supply.
  Dead, it reads
  Output pin at 0 V, or near 0 Ω to ground with the power off: shorted inside.
  Output pin at the full supply voltage: open inside, no current flowing.
  On the board:
  Measured on the board with power on; the bias network is part of the reading.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The figures depend on the part and its bias resistor. The datasheet gives both.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BGX50A, opens in a new tab
- BZT52C18Kprinted U8Zener diode, Taiwan SemiconductorZener diodeNot recordedNot recordedTaiwan Semiconductor
  Printed U8. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Zener diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BZT52C18K, opens in a new tab

Open this in the search to correct a character or try another package.

12 parts are printed U

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Codes that begin with U

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?