SMD marking

5

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

12 parts are printed 5

Not sure which one you have?

Answer up to 4 quick questions and these 12 parts are ranked, with a meter test that settles it. It works on a dead part too.

BAT60BSOD-323Schottky diode, InfineonSchottky diodeSOD-323Infineon
What it is
Schottky diode
Maker
Infineon
Package
SOD-323
Pins
2
Details
Schottky diode, 10 V
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAT60B, opens in a new tab
RB751S-40SOD-523Schottky diode, JSCJSchottky diodeSOD-523JSCJ
What it is
Schottky diode
Maker
JSCJ
Package
SOD-523
Pins
2
Details
Schottky diode, 40 V, 0.03 A
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor RB751S-40, opens in a new tab
10 more parts have no package on record
- AOZ8S305BLS-04ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection for high-speed interfaces
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8S305BLS-04, opens in a new tab
- AOZ8S305BLS-05ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection for high-speed interfaces
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8S305BLS-05, opens in a new tab
- AOZ8S305BLS-12ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection for high-speed interfaces
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8S305BLS-12, opens in a new tab
- AOZ8831DT-05ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection for high-speed interfaces
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8831DT-05, opens in a new tab
- AOZ8850ADI-03ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection for high-speed interfaces
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8850ADI-03, opens in a new tab
- BBY53-03WInfineonNot recordedNot recordedInfineon
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BBY53-03W, opens in a new tab
- BBY57-02VInfineonNot recordedNot recordedInfineon
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BBY57-02V, opens in a new tab
- PMEG2005ESFSchottky diode, NexperiaSchottky diodeNot recordedNexperia
  What it is
  Schottky diode
  Maker
  Nexperia
  Package
  Not recorded
  Pins
  2
  Details
  20 V, 0.5 A low VF MEGA Schottky barrier rectifier
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PMEG2005ESF, opens in a new tab
- RB751G-40Schottky diode, JSCJSchottky diodeNot recordedJSCJ
  What it is
  Schottky diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Schottky diode, 40 V, 0.03 A
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor RB751G-40, opens in a new tab
- RB751M5-40Schottky diode, Taiwan SemiconductorSchottky diodeNot recordedTaiwan Semiconductor
  What it is
  Schottky diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor RB751M5-40, opens in a new tab

11 more parts are printed with a code easy to misread as 5

Printed with a code easy to misread

One character differs, and it is one that is easy to confuse under a lamp. The odd one out is marked on each.

RB521S-40printed SSOD-523Schottky diode, JSCJSchottky diodeSOD-523JSCJ
Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
What it is
Schottky diode
Maker
JSCJ
Package
SOD-523
Pins
2
Details
Schottky diode, 40 V, 0.2 A
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor RB521S-40, opens in a new tab
10 more parts have no package on record
- AOZ8310DI-26printed SESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8310DI-26, opens in a new tab
- BA592printed SDiode, InfineonDiodeNot recordedInfineon
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  Diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways: failed open.
  A reading the wrong way round as well: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BA592, opens in a new tab
- BB535printed SInfineonNot recordedNot recordedInfineon
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BB535, opens in a new tab
- BB639printed SInfineonNot recordedNot recordedInfineon
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BB639, opens in a new tab
- BB640printed SInfineonNot recordedNot recordedInfineon
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BB640, opens in a new tab
- ESDTU5V0A1printed SESD protection diode, JSCJESD protection diodeNot recordedJSCJ
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  ESD protection diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection diode, VRWM 5 V
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESDTU5V0A1, opens in a new tab
- IRLML6244printed SN-channel MOSFET, InfineonN-channel MOSFETNot recordedInfineon
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  N-channel MOSFET
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Details
  20V Single N-Channel StrongIRFET™ Power MOSFET in a SOT-23 package
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor IRLML6244, opens in a new tab
- SD197printed SInfineonNot recordedNot recordedInfineon
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SD197, opens in a new tab
- SD198printed SInfineonNot recordedNot recordedInfineon
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SD198, opens in a new tab
- SD199printed SInfineonNot recordedNot recordedInfineon
  Printed S on the part. Easy to misread as 5. Check that character with a loupe before you order anything.
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SD199, opens in a new tab

27 more parts have codes that begin with 5

Codes that begin with 5

For a marking with its end worn or burnt off. Each one shows its full printed code.

TVS diode, all SMB, 2 pins, all Vishay.

1.5B12Aprinted 5KXSMB
Printed 5KX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B12A, opens in a new tab
1.5B12CAprinted 5KXSMB
Printed 5KX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B12CA, opens in a new tab
1.5B13Aprinted 5KZSMB
Printed 5KZ. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B13A, opens in a new tab
1.5B13CAprinted 5KZSMB
Printed 5KZ. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B13CA, opens in a new tab
1.5B15Aprinted 5LGSMB
Printed 5LG. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B15A, opens in a new tab
1.5B15CAprinted 5LGSMB
Printed 5LG. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B15CA, opens in a new tab
1.5B16Aprinted 5LKSMB
Printed 5LK. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B16A, opens in a new tab
1.5B16CAprinted 5LKSMB
Printed 5LK. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B16CA, opens in a new tab
1.5B18Aprinted 5LMSMB
Printed 5LM. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B18A, opens in a new tab
1.5B18CAprinted 5LMSMB
Printed 5LM. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B18CA, opens in a new tab
1.5B20Aprinted 5LRSMB
Printed 5LR. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B20A, opens in a new tab
1.5B20CAprinted 5LRSMB
Printed 5LR. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B20CA, opens in a new tab
1.5B22Aprinted 5LSSMB
Printed 5LS. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B22A, opens in a new tab
1.5B22CAprinted 5LSSMB
Printed 5LS. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B22CA, opens in a new tab
1.5B24Aprinted 5LVSMB
Printed 5LV. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B24A, opens in a new tab
1.5B24CAprinted 5LVSMB
Printed 5LV. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B24CA, opens in a new tab
1.5B27Aprinted 5LWSMB
Printed 5LW. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B27A, opens in a new tab
1.5B27CAprinted 5LWSMB
Printed 5LW. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B27CA, opens in a new tab
1.5B30Aprinted 5MESMB
Printed 5ME. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B30A, opens in a new tab
1.5B30CAprinted 5MESMB
Printed 5ME. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B30CA, opens in a new tab
1.5B33Aprinted 5MGSMB
Printed 5MG. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B33A, opens in a new tab
1.5B33CAprinted 5MGSMB
Printed 5MG. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B33CA, opens in a new tab
1.5B36Aprinted 5MJSMB
Printed 5MJ. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B36A, opens in a new tab
1.5B36CAprinted 5MJSMB
Printed 5MJ. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B36CA, opens in a new tab
1.5B39Aprinted 5MMSMB
Printed 5MM. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B39A, opens in a new tab
1.5B39CAprinted 5MMSMB
Printed 5MM. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B39CA, opens in a new tab
1.5B43Aprinted 5MNSMB
Printed 5MN. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
TVS diode
Maker
Vishay
Package
SMB
Pins
2
Details
1500 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 1.5B43A, opens in a new tab

Open this in the search to correct a character or try another package.

12 parts are printed 5

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Printed with a code easy to misread

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Codes that begin with 5

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?